时间:2011-06-14 21:45来源:蓝天飞行翻译 作者:航空 点击:次
linear variable differential transduser(LVDT)线性可变位移传感器 linear variable dispalcement transformer (LVDT)线性可变差动转换器 liner 1、轴瓦;衬套2、火焰筒 lining 衬垫;衬板 link 连杆 linkage 连杆装置 lint free 不起毛的 lip 唇边、凸出部 lip seal 碗形封严件 live 可用的、通电的 live engine 在缺陷但仍在运转的发动机 live load 交变载荷 load cell 测力传感器;载荷测力器 load compressor 供气压气机 load limiter 载荷限制器 load meter 测力计 load shedding 电载荷释放 loading coil 加感线圈 loading spectrum 载荷谱 lobe 瓣轮;凸角 local area 局部范围 localizer 定位信标 locating 定位 locating bush/lug 定位衬套/凸块 locating segment 扇形定位件 lockbolt 锁紧螺栓 locked up stress 残存应力 locking collar/spline 锁紧套圈/齿套 locking spider 星形锁片 lock out 1、锁定;2、(舵面的)锁定机构 lockout debooster (刹车)锁闭 减压器 lockout hole 保险丝眼孔 lockring 卡簧圈 lockwahser 锁紧垫圈 lockwiring 保险丝保险 Loctite (一种)粘合剂 V 用LOCTITE 粘合 loft line 放样线 logbook 履历本 logic 逻辑电路 logo light 飞机徽标照明灯 long duct turbofan 涡扇发动机长涵道型 long range navigation(LORAN) 罗兰导航 longeron 大梁;纵梁 longitudinal 纵向的 lingitudinal axis=rool axis 纵轴 loom 1、导线束2、翼肋;腹板 loop 1、环;匝2、活套;3、环路 loop clamp 集束卡箍 loose fit 松配合 Loran 罗兰导航 lost motion device 空回装置 lost wax 失蜡造型 lot 批;批量 louver 1、(火焰筒)散热环罩2、放气窗;百叶窗 low approach thrust 低进近推力 low emission combustion chamber 低污染燃烧室 low limit 下限 low pass filter 低通滤波器 low pressure drive turbine 低压涡轮 low range radio altimeter (LRRA) 低范围无线高度表 low spot 凹点 low wing 下单翼的 lox=liquid oxygen 液氧 lubber line (罗盘)参考标线 lube 润滑油 lube retainer 护油圈 lubricant 润滑剂 lubrcating 添加剂润滑油脂 lucite 有机萤光玻璃;丙烯酸树脂 lug 凸耳;块;环 M-M Mach number 马赫数 mach trim 高速配平 machine bolt 六角头螺栓 machining 机械加工 macro inspection 宏观检查 Magnuflux 磁粉擦伤检查 Magmaglo 磁粉 Magne gauge 镀层测厚量具 magnesyn system 磁同步系统;远距指示系统 magnetic chip detector (MCD) 金属屑磁性检测器 magnetic particle inspection(MPI) 磁粉探伤检查 magnetic tape 磁带 main engine control(MEC)=fuel control unit(FCU)燃油控制器 main equipment center(MEC) 主要设备中心 main line bearing 发动机轴线上的轴承 maintenance 维修 play panel 维修操作显示面板 maintenance error 维修差错 Maintenance Planning Data(MPD) 维护计划文件 Maintenance Program 维修大纲 Maintenance Schedule(MS) 维修计划/方案 maintenance significant items(MSI) 重大维修项目 maintenance tips 维修提示 major alteration 重大改装 major diameter 1、大直径2、螺纹外径 major overhaul 大翻修 major repair 大修 tact 先闭后开式(触点) maladjust(-ment) 失调;失配 malalign(-ment) 不对准;不同轴 male fitting 阳模配合;公接头 malfunction 故障(指直接影响功能的) man-hole door (供人进出检修用)入孔口 mandatory 必须执行的;指令性的 mandatory directive removal 为进行强制性项目而进行的拆卸;指令性拆卸 mandatory replacement item 强制性更换件 mandrel (mandril) 芯轴 manifold 总管 manipularing key 手动键 manual 1、手动的2、手册的 map 特性曲线图 margin 1、边缘2、极限3、裕度 margin tolerance 公差范围 marginal performance 极限性能;限界性能 mark 1、型记2、标记 making off 打印记;划线 making up 标出裂纹位置 marshalling 集件 mask 面罩 ;v.遮护 masking tape 遮护胶带 mass flow 单位流量 mass memory 大容量在储器 mast 1、泄油管柱2、天线杆 master 标准样件; 主控台 master dim&test system 主减光设备和检测 match 匹配;偶合 mated 匹对的 matrix 基本的;(计)矩阵存储器 maximum 最大的;n.最大值 maximum continuous thrust 最大持续推力 |